/diy/ - Do It Yourself

>>2782116
ofc I don't know how to use it I bought it to learn along with a book and the manual on github

>>2753655
Not him, but I live in Florida and we do this. Had one get out of control and wound up in the local paper after the fire department, department of forestry, and sheriff's department showed up. Pretty sure the power company got involved as well. Shit was fire

>>2727615
sewing isn't complicated so much as it's a lot of little things in there, but everyone here for the most part are going to tell you the same thing

>>2727610
legit, just youtube the shit out of it.

Hey guys, this is the OP BTW, I don't know what my trip is but I'm gonna start a new thread soon, I think we should be fine till Monday, but I'll go ahead and something started sense we are red anyway.

For the time being, if you have suggestions to add to the start, reply to me on this one and I'll add it.

>>2727539
Georgia, I don't believe so

>>2727301
scale?

>>2678452
What are you sewing? I sew a lot of faux fur and I have a Bernina and I use 110/18 needles.

>>2656404
Well if i actually wanna do so why am i asking you

>>2653548
Holy shit dude! That's fucking amazing! Good job my guy!

>>2651994
I just cheapo chalk from walmart with a pencil sharpner. works well. If I'm cutting on that fabric, I'll just use a sharpie

>>2651324
2" is normally fine as long as you pin it right.

>>2649503
I'm saying the type of person who straight up takes their shit and turns it BACK into soil. Like the entire process.

>>2649123
you make me think that you save your shit for fertilizer

>>2648087
muslin

>>2630026

what this dude said, >>2630065 but change it up ever so slightly so when someone tries to claim it say, "I made it different and it's my own design" and people can't do shit!

Who actually watches this shit

>>2021430>
Dipped, but not for all the reasons posted here already. Because it's far more chemical/oil/solvent resistant. That's in fact why they offer the option, and why many oilfield and mechanics tools only come dipped. That thermocast plastic shit turns to goose shit when it gets solvent or oil on it.

PCD fiber cement blade in an angle grinder or joint chaser. Trick is you gotta REALLY be soft on the sides cuz it'll blow the teeth off quick if you push into the concrete.

Alternatively grind a small jackhammer bit to the joint width and make it as sharp as a knife. Run it into the groove and you'll pop out small chunks if you don't just shove it super deep.

No matter how you do bitumen is shit to deal with. Best method is burn down all the suppliers storage yards. Shit burn HOT yo!

>>1917513
This. I used to work night shift and we all did this.

>>1911635
>>buying a french vehicle
Not even once

>>1839545
Lol
>>Tommy tycoon
>>Kiking out the capsi industry
>>Industrial espionage and wholesale flagrant market manipulation
Based humongous poster, keep it up.

>>1839545
Lol
>>Tommy tycoon
>>Kiking out the capsi industry
>>Industrial espionage and wholesale flagrant market manipulation on the wholesale
Based humongous poster, keep it up.

>>1829875
This thread is full of so much wrong it's not funny.

>>1830060
Single component caulking is to multicomponent jacking compound what a hammer drill is to a boring rig. Don't waste your time on this ffs.

Poly is expensive, look for a local mudjacking company that uses good ole grout. It's more than fine for a driveway, and a lot cheaper. If you can figure out a way to build a DIY grout pump then you can just use high flow grout (same as used for post-tensioning cable pockets). This is a perfectly legitimate solution as mudjacking has been proven effective for like 100 years.

>>1830029
This is basically the proper solution, and make sure this time to get proper compaction of your footing with the right material and edge grading so it doesn't erode.